Glass Finish

Execute your timber finish to the highest standard with Feast Watson Glass Finish.

Glass Finish provides a beautiful glass-like, high-gloss finish to furniture and timber, and with only one coat, is equivalent to 60 coats of traditional varnish. Why would you want anything else?

It is a two-part, high build epoxy resin for timber that is extremely durable, hard wearing, and scratch-resistant - perfect for small craft or decoupage projects, and highly recommended for interior timber benches and tabletops.

Glass Finish also provides the flexibility to tint with Prooftint, providing a vast range of colour options.

It is the one and only tool to achieve your beautiful timber finish.

Note:

Glass Finish is NOT suitable for exterior timber, flooring, or vertical surfaces.
Feast Watson Glass Finish Kit includes: Glass Finish RESIN (Part A), Glass Finish HARDENER (Part B), Stirrer, Glass Finish Usage Guide.
ALWAYS REFER TO THE INSTRUCTIONS ON THE CONTAINERS AND THE GLASS FINISH USAGE GUIDE BEFORE COMMENCING YOUR PROJECT.

Safety Data Sheet

Find a stockist

WHERE TO USE

All interior timber furniture and accessories. Ideal for small craft or decoupage projects, and highly recommended for interior timber benches and tabletops. Suitable as an embedding or casting medium.

FINISH

Gloss

COVERAGE RATE

1m² Kit

NUMBER OF COATS

1 Coat

DRY TIME

Touch dry - 24 hours
Light use - 36 hours
Full cure - 7 Days

CLEAN UP

Epoxy Thinners

SIZES

1m² Kit

How to prepare my timber for Feast Watson Glass Finish:

Before you get started:

Ensure your surface is dry and free from dust, grease, wax, or oil.
Ensure the surface is level.

How to set up your work area:

The surface should be elevated from the work area about 2 inches to allow the coating to drip freely off the sides of the item being coated.
Place aluminium, plastic sheeting, or wax paper underneath the item being coated to catch drips.
Use tape to cover areas that you do not want coated.

We recommend sealing the surface with a suitable sealer before applying Glass Finish.

How to apply Feast Watson Glass Finish:

*ALWAYS REFER TO THE INSTRUCTIONS ON THE FEAST WATSON CONTAINERS AND THE GLASS FINISH USAGE GUIDE BEFORE COMMENCING YOUR PROJECT.

Do NOT thin Glass Finish

Combine

1. Combine all of Glass Finish RESIN (Part A) into Glass Finish HARDENER (Part B) in a clean container.
  - Note: Refer to Glass Finish Usage Guide for advice on how to measure out a smaller amount of Glass Finish to complete a smaller project than that allowed for in kit size.

Mix

1. Mix combined RESIN and HARDENER with the flat stirrer provided until the material is thoroughly blended (refer to mixing instructions in pack). Product will not cure properly or final finish will be soft or sticky if mixing directions are not followed.

Pour and Spread

1. As soon as the product is mixed, pour over the surface that is to be coated.
  - Caution: If product is left in mixing container it will become hot and set rapidly.
2. Spread evenly with a brush or spreader. Do NOT roll or spray.
3. After pouring you have approximately 25 minutes working time before Glass Finish starts to harden.

Degass

1. If bubbles occur after about 5 minutes, they can be easily and effectively broken. Just gently exhale onto them until they disappear.
2. A propane torch is recommended to remove bubbles from a freshly coated surface. Sweep area with the propane torch from 15cm above surface until bubbles disappear. Use a low flame. Do NOT hold torch in one area for too long. (Note: Avoid inhaling fumes).
  - Note: It is carbon dioxide, not heat which breaks up bubbles. Do NOT use a heater or a hair dryer. Do NOT try to remove bubbles after 30 minutes.
  - Tidy up edges with a small brush

Cure

1. Leave to dry in a dust free area for 24 hours
2. For best results, room temperature should be at least 23 degrees

Looking to Stain?

To change the colour of Glass Finish, add up to 2% Feast Watson Prooftint when mixing RESIN and HARDENER (Step 2)

MAINTENANCE

How to maintain my timber after using Feast Watson Glass Finish:

If required, wipe down surface with a soft damp cloth.
If deep scratches occur, lightly sand surface and reapply one coat of Glass Finish as per application instructions.

How to maintain my timber after using Feast Watson Glass Finish:

If required, wipe down surface with a soft damp cloth.
If deep scratches occur, lightly sand surface and reapply one coat of Glass Finish as per application instructions.

PREPARATION

How to prepare my timber for Feast Watson Glass Finish:

Before you get started:

Ensure your surface is dry and free from dust, grease, wax, or oil.
Ensure the surface is level.

How to set up your work area:

The surface should be elevated from the work area about 2 inches to allow the coating to drip freely off the sides of the item being coated.
Place aluminium, plastic sheeting, or wax paper underneath the item being coated to catch drips.
Use tape to cover areas that you do not want coated.

We recommend sealing the surface with a suitable sealer before applying Glass Finish.

APPLICATION

How to apply Feast Watson Glass Finish:

*ALWAYS REFER TO THE INSTRUCTIONS ON THE FEAST WATSON CONTAINERS AND THE GLASS FINISH USAGE GUIDE BEFORE COMMENCING YOUR PROJECT.

Do NOT thin Glass Finish

Combine

1. Combine all of Glass Finish RESIN (Part A) into Glass Finish HARDENER (Part B) in a clean container.
  - Note: Refer to Glass Finish Usage Guide for advice on how to measure out a smaller amount of Glass Finish to complete a smaller project than that allowed for in kit size.

Mix

1. Mix combined RESIN and HARDENER with the flat stirrer provided until the material is thoroughly blended (refer to mixing instructions in pack). Product will not cure properly or final finish will be soft or sticky if mixing directions are not followed.

Pour and Spread

1. As soon as the product is mixed, pour over the surface that is to be coated.
  - Caution: If product is left in mixing container it will become hot and set rapidly.
2. Spread evenly with a brush or spreader. Do NOT roll or spray.
3. After pouring you have approximately 25 minutes working time before Glass Finish starts to harden.

Degass

1. If bubbles occur after about 5 minutes, they can be easily and effectively broken. Just gently exhale onto them until they disappear.
2. A propane torch is recommended to remove bubbles from a freshly coated surface. Sweep area with the propane torch from 15cm above surface until bubbles disappear. Use a low flame. Do NOT hold torch in one area for too long. (Note: Avoid inhaling fumes).
  - Note: It is carbon dioxide, not heat which breaks up bubbles. Do NOT use a heater or a hair dryer. Do NOT try to remove bubbles after 30 minutes.
  - Tidy up edges with a small brush

Cure

1. Leave to dry in a dust free area for 24 hours
2. For best results, room temperature should be at least 23 degrees

Looking to Stain?

To change the colour of Glass Finish, add up to 2% Feast Watson Prooftint when mixing RESIN and HARDENER (Step 2)

MAINTENANCE

How to maintain my timber after using Feast Watson Glass Finish:

If required, wipe down surface with a soft damp cloth.
If deep scratches occur, lightly sand surface and reapply one coat of Glass Finish as per application instructions.

MAINTENANCE

How to maintain my timber after using Feast Watson Glass Finish:

If required, wipe down surface with a soft damp cloth.
If deep scratches occur, lightly sand surface and reapply one coat of Glass Finish as per application instructions.

System.IO.IOException: The process cannot access the file 'C:\local\Temp\ExamineIndexes\87b109f06c75ad52504281172cd4c66b\ContentIndex\_15.cfs' because it is being used by another process.
   at System.IO.FileSystem.DeleteFile(String fullPath)
   at System.IO.FileInfo.Delete()
   at Examine.Lucene.Directories.SyncedFileSystemDirectoryFactory.ClearDirectory(DirectoryInfo directoryInfo)
   at Examine.Lucene.Directories.SyncedFileSystemDirectoryFactory.SyncIndex(IndexWriter sourceIndexWriter, Boolean forceUnlock, String indexName, DirectoryInfo destinationDirectory, DirectoryInfo tempDir)
   at Examine.Lucene.Directories.SyncedFileSystemDirectoryFactory.TryCreateDirectory(LuceneIndex luceneIndex, Boolean forceUnlock, Directory& directory)
   at Examine.Lucene.Directories.SyncedFileSystemDirectoryFactory.CreateDirectory(LuceneIndex luceneIndex, Boolean forceUnlock)
   at Examine.Lucene.Directories.DirectoryFactoryBase.Examine.Lucene.Directories.IDirectoryFactory.CreateDirectory(LuceneIndex luceneIndex, Boolean forceUnlock)
   at Umbraco.Cms.Infrastructure.Examine.ConfigurationEnabledDirectoryFactory.CreateDirectory(LuceneIndex luceneIndex, Boolean forceUnlock)
   at Examine.Lucene.Directories.DirectoryFactoryBase.Examine.Lucene.Directories.IDirectoryFactory.CreateDirectory(LuceneIndex luceneIndex, Boolean forceUnlock)
   at Examine.Lucene.Providers.LuceneIndex.<>c__DisplayClass1_0.<.ctor>b__0()
   at System.Lazy`1.ViaFactory(LazyThreadSafetyMode mode)
   at System.Lazy`1.ExecutionAndPublication(LazyHelper executionAndPublication, Boolean useDefaultConstructor)
   at System.Lazy`1.CreateValue()
   at System.Lazy`1.get_Value()
   at Examine.Lucene.Providers.LuceneIndex.GetLuceneDirectory()
   at Examine.Lucene.Providers.LuceneIndex.IndexExistsImpl()
   at Examine.Lucene.Providers.LuceneIndex.IndexExists()
   at Examine.Lucene.Providers.LuceneIndex.EnsureIndex(Boolean forceOverwrite)
   at Examine.Lucene.Providers.LuceneIndex.get_IndexWriter()
   at Examine.Lucene.Providers.LuceneIndex.CreateSearcher()
   at System.Lazy`1.ViaFactory(LazyThreadSafetyMode mode)
--- End of stack trace from previous location ---
   at System.Lazy`1.CreateValue()
   at Examine.Lucene.Providers.LuceneIndex.get_Searcher()
   at DuluxGroup.CMSWeb.Services.ContentIndexQueryService.GetContentsBySearchRequestModel(String indexName, String[] includeNodeTypeAliases, SearchRequestModel searchRequestModel) in D:\a\1\s\src\DuluxGroup.CMSWeb\Services\ContentIndexQueryService.cs:line 79
   at DuluxGroup.CMSWeb.Services.ItemListingService.GetContentsByStarterNodeAndCriteria(ItemListingSource itemListingSource, IEnumerable`1 criteria) in D:\a\1\s\src\DuluxGroup.CMSWeb\Services\ItemListingService.cs:line 244
   at DuluxGroup.CMSWeb.Services.ItemListingService.GetContentInfoModelsFromChildNode(ItemListingSource itemListingSource, Int32 numberOfDisplayItems) in D:\a\1\s\src\DuluxGroup.CMSWeb\Services\ItemListingService.cs:line 140
   at DuluxGroup.CMSWeb.Services.ItemListingService.GetSortedAndOrderedContentInfos(ItemListingSource itemListingSource, Int32 numberOfDisplayItems) in D:\a\1\s\src\DuluxGroup.CMSWeb\Services\ItemListingService.cs:line 114
   at DuluxGroup.CMSWeb.Services.ItemListingService.GetViewModel(ItemListing itemListing) in D:\a\1\s\src\DuluxGroup.CMSWeb\Services\ItemListingService.cs:line 47
   at AspNetCore.Views_Partials_grid_editors_DocTypeGridEditor_itemListing.ExecuteAsync()
   at Microsoft.AspNetCore.Mvc.Razor.RazorView.RenderPageCoreAsync(IRazorPage page, ViewContext context)
   at Microsoft.AspNetCore.Mvc.Razor.RazorView.RenderPageAsync(IRazorPage page, ViewContext context, Boolean invokeViewStarts)
   at Microsoft.AspNetCore.Mvc.Razor.RazorView.RenderAsync(ViewContext context)
   at Microsoft.AspNetCore.Mvc.ViewComponents.ViewViewComponentResult.ExecuteAsync(ViewComponentContext context)
   at Microsoft.AspNetCore.Mvc.ViewComponents.DefaultViewComponentInvoker.InvokeAsync(ViewComponentContext context)
   at Microsoft.AspNetCore.Mvc.ViewComponents.DefaultViewComponentHelper.InvokeCoreAsync(ViewComponentDescriptor descriptor, Object arguments)
   at Our.Umbraco.DocTypeGridEditor.Helpers.DocTypeGridEditorHelper.RenderDocTypeGridEditorItem(IViewComponentHelper helper, IHtmlHelper htmlHelper, IPublishedElement content, String editorAlias, String viewPath, String previewViewPath, Boolean isPreview) in D:\a\1\s\src\Our.Umbraco.DocTypeGridEditor\Helpers\DocTypeGridEditorHelper.cs:line 254
   at Our.Umbraco.DocTypeGridEditor.Helpers.DocTypeGridEditorHelper.RenderDocTypeGridEditorItem(IViewComponentHelper helper, IHtmlHelper htmlHelper, Object model) in D:\a\1\s\src\Our.Umbraco.DocTypeGridEditor\Helpers\DocTypeGridEditorHelper.cs:line 222
   at CallSite.Target(Closure, CallSite, Object)
   at AspNetCore.app_plugins_doctypegrideditor_render_doctypegrideditor.ExecuteAsync() in C:\home\site\wwwroot\app_plugins\doctypegrideditor\render\doctypegrideditor.cshtml:line 4
   at Microsoft.AspNetCore.Mvc.Razor.RazorView.RenderPageCoreAsync(IRazorPage page, ViewContext context)
   at Microsoft.AspNetCore.Mvc.Razor.RazorView.RenderPageAsync(IRazorPage page, ViewContext context, Boolean invokeViewStarts)
   at Microsoft.AspNetCore.Mvc.Razor.RazorView.RenderAsync(ViewContext context)
   at Microsoft.AspNetCore.Mvc.ViewFeatures.HtmlHelper.RenderPartialCoreAsync(String partialViewName, Object model, ViewDataDictionary viewData, TextWriter writer)
   at Microsoft.AspNetCore.Mvc.ViewFeatures.HtmlHelper.PartialAsync(String partialViewName, Object model, ViewDataDictionary viewData)
   at AspNetCore.Views_Partials_grid_editors_base.ExecuteAsync() in C:\home\site\wwwroot\Views\Partials\grid\editors\base.cshtml:line 6